DIY Bracelet Kit – Black Lava, Rose Quartz & Natural Wood
A ready-to-make bracelet kit with an earthy, boho feel. Matte black lava stone beads, small soft pink rose quartz beads and light natural wooden beads mix three sizes (6mm, 4mm and 8mm) for a layered look. No clasp is needed — the bracelets slide on and off. Make them for yourself, for friends, or as gifts.
What’s included
- 1 × 6mm black lava strand — 64 round black lava stone beads on a 37cm strand, hole about 1mm. Porous, so they work as an essential oil diffuser.
- 1 × 4mm rose quartz strand — about 85 round beads on a 35cm strand, hole about 1mm. Natural rose quartz, dyed for an even soft pink.
- 60 × 8mm natural wooden beads — round, unfinished natural wood, hole about 2mm. Lightweight and easy to thread.
- 1 × 5m black stretch cord — 1mm black elastic beading cord. Cut about 25cm per bracelet, including extra for knotting.
How many bracelets?
An average adult wrist is about 18cm (7 inches). This kit makes 6 adult bracelets, each with about 10 black lava beads (6mm), 9 wooden beads (8mm) and 12 rose quartz beads (4mm). That is about 6cm + 7.2cm + 4.8cm = 18cm of beads per bracelet.
Six bracelets use 60 of the 64 lava beads, 54 of the 60 wooden beads and about 72 of the 85 rose quartz beads, so you have a few spares for fine-tuning the fit. Strands can vary by a bead or two, so check the fit and add or remove a small rose quartz bead as needed. Bigger wrists need a few more beads per bracelet, which may make 5 larger bracelets instead. Six bracelets use about 1.5m of the 5m cord.
How to make a stretch bracelet
- Measure your wrist, or use 18cm (7 inches) for an average adult size. Cut about 25cm of stretch cord (wrist size plus 6–7cm for knotting).
- Gently stretch the cord a few times before threading so the finished bracelet doesn’t loosen later. A little tape on one end stops beads sliding off.
- Cut the strands open over a tray so loose beads don’t roll away.
- Thread your beads: for example a run of 10 black lava beads on top, then alternate wooden beads with small groups of rose quartz around the rest (wood, 1–2 rose quartz, wood, and so on). Or try a repeating pattern of wood, lava, rose quartz, lava.
- Check the fit around your wrist and add or remove rose quartz beads to fine-tune the length.
- Tie a surgeon’s knot or a tight double knot, pull it snug, and trim the tails. A small drop of clear jewellery glue on the knot is optional. Slide the knot inside a wooden bead — their larger 2mm hole hides it nicely.
Tips
- Aromatherapy diffuser tip: lava stone is naturally porous. Put one drop of your favourite essential oil on two or three lava beads, let it soak in for a minute, then wear the bracelet. The scent is released slowly over a few days. Keep oil off the wood and rose quartz (oil can darken unfinished wood) and wipe off any excess.
- Unfinished wood can absorb water, so take the bracelet off before swimming or showering.
- The 4mm rose quartz beads have small holes, so a needle-free trick is to cut the cord end at an angle or stiffen it with a dab of clear nail polish.
Specifications
- Lava beads: 6mm round, 64 beads, 37cm strand, hole about 1mm, natural black lava stone
- Rose quartz beads: 4mm round, about 85 beads, 35cm strand, hole about 1mm, natural rose quartz (dyed)
- Wooden beads: 8mm round, 60 beads, hole about 2mm, natural unfinished wood
- Cord: 5 metres of 1mm black stretch beading cord
- Suitable for 18cm / 7 inch adult wrists (adjust the bead count for a smaller or larger size)







Reviews
There are no reviews yet.