DIY Bracelet Kit – Teal Lava, Amber-Look & Natural Wood
A ready-to-make bracelet kit in a relaxed coastal palette. Matte blue-green teal lava stone, glossy golden amber-look resin and light unfinished wood combine three textures for an easy boho look. No clasp is needed — the bracelets slide on and off. Make them for yourself, for friends, or as gifts.
What’s included
- 2 × 6mm teal lava strands — about 60 round dyed lava stone beads per 37cm strand (about 120 beads in total), hole about 1mm. Porous, so they work as an essential oil diffuser.
- 25 × 8mm amber-look resin beads — round gold resin beads with an imitation amber finish, hole about 2mm. Lightweight.
- 90 × 8mm natural wooden beads — round unfinished wood beads, hole about 2mm.
- 1 × 5m black stretch cord — round elastic beading cord, about 1mm thick. Cut about 25cm per bracelet, including extra for knotting.
How many bracelets?
An average adult wrist is about 18cm (7 inches). This kit makes 8 adult bracelets, each with about 14 teal lava beads (6mm), 9 wooden beads (8mm) and 3 amber-look beads (8mm). That is about 8.4cm + 7.2cm + 2.4cm = 18cm of beads per bracelet.
Eight bracelets use about 112 of the 120 lava beads, 72 of the 90 wooden beads and 24 of the 25 amber-look beads, so you have spares for fine-tuning the fit. Strands can vary by a bead or two, so check the fit and add or remove a lava or wooden bead as needed. Bigger wrists need a few more beads per bracelet, which may make 7 larger bracelets instead. Eight bracelets use about 2m of the 5m cord, so there is plenty left over for repairs or more projects.
How to make a stretch bracelet
- Measure your wrist, or use 18cm (7 inches) for an average adult size. Cut about 25cm of stretch cord (wrist size plus 6–7cm for knotting).
- Gently stretch the cord a few times before threading so the finished bracelet doesn’t loosen later. A little tape or a bulldog clip on one end stops beads sliding off.
- Cut the teal lava strands open over a tray so the beads don’t roll away.
- Thread your beads: for example a repeating pattern of 2 lava, 1 wood, with an amber-look bead every third or fourth repeat. Or group the 3 amber-look beads at the top with wood either side and lava around the rest.
- Check the fit around your wrist and add or remove a bead to fine-tune the length.
- Tie a surgeon’s knot or a tight double knot, pull it snug, and trim the tails. A small drop of clear jewellery glue on the knot is optional. Gently slide the knot inside a wooden or amber-look bead (they have bigger 2mm holes) to hide it.
Tips
- Aromatherapy diffuser tip: lava stone is naturally porous. Put one drop of your favourite essential oil on two or three lava beads, let it soak in for a minute, then wear the bracelet. The scent is released slowly over a few days. Unfinished wood also soaks up oil, so put the oil on the lava beads only and wipe off any excess.
- The teal lava is dyed, so keep the bracelet dry: take it off before swimming or showering, and wipe it with a soft dry cloth.
- Roll the bracelet on and off rather than over-stretching it, and it will keep its shape longer.
Specifications
- Lava beads: 6mm round, 2 strands of about 60 beads (37cm each), hole about 1mm, natural volcanic lava stone dyed teal
- Amber-look beads: 8mm round, 25 beads, hole about 2mm, gold resin with imitation amber finish
- Wooden beads: 8mm round, 90 beads, hole about 2mm, natural unfinished wood
- Cord: 5 metres of black round stretch beading cord, about 1mm
- Suitable for 18cm / 7 inch adult wrists (adjust the bead count for a smaller or larger size)







Reviews
There are no reviews yet.